W220 Mercedes
+ Mercedes-Benz Cars of a class S (W220)
+ Operation manual
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Automatic transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
Specifications
Diagnostics of malfunctions of onboard electric equipment - the general information
Check of the electric motor of a screen wiper
Check of warmed back glass
Replacement of filament lamps
Function of reserve light
Electric safety locks
Installation of electric and electronic devices
Elements of the uniform lock
Arrangement of the basic electric elements of system of electric equipment of a body of the car
Anticreeping alarm system
+ electric equipment Cхемы
|
Replacement of filament lamps
|
|
Lamp of the back index of turn |
|
|
Lamp of the left parking light |
|
|
Lamp of illumination of registration plate |
|
|
Lamp of a back foggy lamp |
|
|
Lamp of the index of turn of E2e5 |
|
|
Lamp of the index of the right turn, built in a rear-view mirror |
|
|
Headlight regulator. The left is shown |
There is a danger of a travmirovaniye!
Filament lamps and holders of lamps can appear very hot. Therefore before replacement of filament lamps wait coolings of the lighting device.
Store lamps in a place inaccessible to children.
Do not apply the fallen lamps or lamps with scratches, they can burst.
Replacement of lamp Н7
the lamp is under pressure. Therefore it is necessary to put on goggles and gloves.
Headlights with a xenon passing beam:
There is a danger of a travmirovaniye owing to a high voltage!
Replacement of lamps on xenon headlights of a passing beam do not make independently. Work on headlights of a passing beam charge only to experts.
|
|
Before replacement of filament lamps switch off illumination of the car in order to avoid short circuit.
Take a lamp in hands only using a pure napkin made of cloth without pile or a similar material. Fingers should be dry and pure!
Apply only the filament lamps calculated on tension 12 In, the same type and the corresponding capacity. |
Regularly check a tilt angle of headlights.
Forward block headlight
Halogen headlights
Fog light
Halogen headlights
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases-1-.
3. Disconnect the tip from a lamp.
4. Unhook holding spring and take out the filament lamp.
5. Insert the new filament lamp so that the socle entered into dredging of the boss.
6. Hang holding spring and get the tip on a lamp.
7. Establish a cover of the case-1-and fix. |
|
Marker lights
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases-1-.
3. Extend the holder of a lamp.
4. Extend the filament lamp.
5. Press the filament lamp.
6. Press the holder of a lamp.
7. Establish a cover of the case-1-and fix. |
|
Passing beam, driving beam
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases (1 or 2).
3. Disconnect the tip from a lamp.
4. Unhook holding springs and take out the filament lamp.
5. Insert the new filament lamp so that the socle entered into dredging of the boss.
6. Hang holding springs and get the tip on a lamp.
7. Establish a case cover (1 or 2) and fix. |
|
Lamp of the index of turn
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases-2-.
3. The holder with the filament lamp turn to the left and remove. Press the filament lamp, turn it to the left and take out.
4. Insert the filament lamp and turn to the right.
5. Establish the holder of the filament lamp and fix turn to the right.
6. Establish a cover of the case-2-and fix. |
|
Xenon headlights
There is a danger of a travmirovaniye owing to a high voltage!
Cover of a xenon passing beam do not dismantle.
Fog light
Xenon headlights
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases-1-.
3. Disconnect the tip from a lamp.
4. Unhook holding spring and take out the filament lamp.
5. Insert the new filament lamp in a way that the socle entered into dredging of the boss.
6. Hang holding spring and get the tip on a lamp.
7. Establish a cover of the case-1-and fix. |
|
Marker lights
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases-1-.
3. Extend the holder of a lamp.
4. Extend the filament lamp.
5. Press the filament lamp.
6. Press the holder of a lamp.
7. Establish a cover of the case-1-and fix. |
|
Decree lamp
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases-1-.
3. Disconnect the tip from a lamp.
4. Unhook holding springs and take out the filament lamp.
5. Insert the new filament lamp so that the socle entered into dredging of the boss.
6. Hang holding springs and get the tip on a lamp.
7. Establish a cover of the case-1-and fix. |
|
Lamp of the index of turn
|
|
|
1. Open a cowl.
2. Compress хомутик and uncover cases-2-.
3. The holder with the filament lamp turn to the left and remove. Press the filament lamp, turn it to the left and take out.
4. Insert the filament lamp and turn to the right.
5. Establish the holder of the filament lamp and fix turn to the right.
6. Establish a cover of the case-2-and fix. |
|
Back lamp
|
|
|
1. Open a trunk lid.
2. A covering take aside.
3. The holder with the filament lamp turn to the left and remove.
4. Press the filament lamp, turn it to the left and take out.
5. Insert the filament lamp and turn to the right.
6. Establish the holder of the filament lamp and fix turn to the right. |
|
Additional lamps of the index of turn on an external rear-view mirror, the top lamp of a signal of braking and lamps of a signal of braking
Additional lamps of the index of turn on an external rear-view mirror, the top lamp of a signal of braking (the 3rd lamp of a signal of braking) and lamps of a signal of braking in back lamps are equipped with light-emitting diodes.
At malfunction or refusal address on one of Mercedes-Benz stations.
Partial sticking up of headlights
In the countries with the order of movement different from an order of movement in the country of the admission of the car to operation, it is necessary to stick headlights partially.
Stickers can be got at any Mercedes-Benz station. It is recommended to apply for this purpose only firm stickers. Other stickers can cause damages of a superficial protective layer of headlights. |
|