Mercedes S-Class W-220

since 1998 of release

Repair and car operation



W220 Mercedes
+ Mercedes-Benz Cars of a class S (W220)
+ Operation manual
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Automatic transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Security measures at carrying out body works
   Cleaning and care of the car
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Replacement of brushes of screen wipers
   Orthopedic seats
   Heating of seats
   Replacement of the filter of purification of air of salon
   Sensors of electric systems
   Fire extinguishing system
+ Onboard electric equipment
+ electric equipment Cхемы






Orthopedic seats

Orthopedic seat (FDS) (from 09.2002 g, codes 433 and 434)

1 — the Airbag in shoulders (double }
2 — the Lateral airbag

3 — the Airbag for maintenance of the top and bottom areas of a waist


Orthopedic seat (MCS)

1 — Two airbags in shoulders
2 — Two airbags on each side

3 — Three airbags of a dlyapodderzhaniye of a waist
4 — Switches


Heating of seats

1 — Management of heating of seats through CAN
2 — Activation of light-emitting diodes in the control unit N69/3s7 door through CAN
N25/6 — the Control unit a back seat of N69/4
N32/1 — the Control unit adjustment of the left forward N69/4s6 of a seat with memory
N32/2 — the Control unit adjustment of the right forward N69/4s7 of a seat with memory
N69/1 — the Control unit the left forward door of R13/1
N69/ls10 — the Switch of modes 1 and 2 of heating of R13/2 or only a mode of 1 heating of a seat
N69/ls11 — the Switch of ventilation of a seat or' R13/3 a mode 2 heatings of a seat of R13/4
N69/2 — the Control unit the right forward door
N69/2s10 — Heating of a seat in modes' and 2 or only in R13/5 the R13/6 mode 1
N69/2sl 1 — Ventilation of a seat or a mode 2 heatings of R13/7 of a seat of R13/8
N69/3 — the Control unit the left back door
N69/3S6 — Heating of a seat in modes 1 and 2 or only in a mode 1
N69/3s — Ventilation of a seat or a mode 2 heatings of a seat
N69/4 — the Control unit the right back door

N69/4s6 — Heating of a seat in modes 1 and 2 or only in a mode 1
N69/4s7 — Ventilation of a seat or we will solve 2 heatings of a seat
R13/1 — the Warmed-up pillow of the left forward seat
R13/2 — the Warmed-up pillow of a back of the left forward seat
R13/3 — the Warmed-up pillow of the right forward seat
R13/4 — the Warmed-up pillow of a back of the right forward seat
R13/5 — the Warmed-up pillow of the left back seat
R13/6 — the Warmed-up pillow of a back of the left back seat
R13/7 — the Warmed-up pillow of the right back seat
R13/8 — the Warmed-up pillow of a back of the right back seat


The description is provided for a driver's seat and fully treats as well a forward passenger seat.


Dynamic (orthopedic) seats (FDS) differ a multicircuit design of an adjustable back with function of memory (MMKL), and also a dynamic lateral emphasis. The Mnogokonturnost of a back is provided with three groups of the airbags providing the top and bottom humeral, lateral both top and bottom lumbar emphasis. The form of a surface and rigidity of a back are regulated manually by means of Group of the corresponding switches of driver's (S109) or forward passenger (S108) of a seat and function of «a dynamic lumbar emphasis».

Dynamic cross-section emphasis (forward seats)

Requirements to function:

• Contour of 15 R Vkl;
• Contour 15 Vkl:
• Adequacy of level of tension (without differences up or down);
• Lack of a signal of the sensor overheat,
• Absence of leakages of air from pillows.

Function activation/deactivation «a dynamic cross-section emphasis» is provided with means of the push-button FDS switch and supervised by the module of management of adjustment of a seat (N32/19). The fact of activation of function proves to be true operation of the control light-emitting diode built in in the FDS button. After function activation the module of management of a seat during commission of turns provides demanded pumping of pillows of the lateral emphasis being in the outer side of a curve of turn. Necessary information on the current cross-section overloads arrives from the module of management of protivozanosny system (N47) and is transferred by the module of management of the central gateway lock (N93) from the tire CAN-C in an impellent compartment to the salonny tire CAN-B. At interruption of a data flow of FDS more than for 2 seconds there is an automatic shutdown of function.

Degree and speed of filling of airbags are regulated at the second level of management of a control panel (А1).

Sports mode (condition 1)

Pressure in pillows of a lateral emphasis is forced quicker and to higher value.
Comfortable mode (condition 2)

Pressure is forced more slowly and to smaller value. Into number of the modules involved in management of dynamic adjustments of seats enter:

• Module of management of a voditelskogosidenye (N32/19);
• Module of management of a forward passenger seat (N32/22);
• Module of management of a tsentralnogomezhsetevy lock (N93);
• Module of management of protivozanosny system (N47).

Priorities of activation of an emphasis

• Priority 1. Lumbar emphasis;
• Priority 2. A humeral emphasis (except individual back seats);
• Priority 3: Cross-section emphasis;
• Priority 4: A dynamic lumbar emphasis and a dynamic lateral emphasis (only for forward seats)

At simultaneous use of several managing directors of switches function of the highest priority is activated only.

Criteria of shutdown

Automatic deactivation of all functions occurs at jumps of level of supply voltage. To shutdown of individual function can lead an overheat of gates and formation of leakages of air.

Background functions

The group of pillows of a lumbar emphasis functions with paired overlapping in wavy sequence. As in each case one pillow is activated only, the next pillows are considered as inactive, i.e. empty. The background functions listed below provide the corresponding conditions for maintenance of the correct mode of functioning of pillows.

Mode of a stravlivaniye of air from inactive pillows (function of an additional complete set)

At maintenance of constant pressure in an active pillow (the resident period) air from the next inactive pillows is issued.

Background dumping of pressure

At an air stravlivaniye from an active pillow residual air from the next inactive pillows at the moment of a sravnivaniye of pressure also is issued.

Limit of dumping of pressure

At achievement of a point of appointment at the moment of end of a wave of a lumbar emphasis the active pillow is devastated on command from the switch, but not further than within 1 minute.

Management functions

Control of a rating of individual pillows of persistent areas in each case is carried out by the module of management of the corresponding seat (N32/19 and N32/22) and is imperceptible for the user with preservation of manual adjustments.

Additional adjustments are made, for example, in case of the fluctuations of pressure connected with change of provision of sitting, leakages of devices of pumping of air, the temperature changes caused by activation/deactivation of elements of heating of seats and streams of heat from system of a conditioning/body sitting, etc.

The sharp pressure jumps caused by changes of situation sitting, are extinguished quickly and imperceptibly. Operating parameters can be programmed in the course of diagnostics.